Mix the self-leveled fast-setting Ultraplan Eso/23-Ultraplan ec
- 14400 KZT/pcs - from 10 pcs
- Customer pickup,
- Courier
- In detail
- BrandMapei
- Country of manufactureItaly
- Weight23 kg
- ColorGrey
CLASSIFICATION ACCORDING TO 13813
According to norms of EN 1381, the leveling structures made by means of Ultraplan Eco have classification of CT - C25 - F7 - A2fl.
SCOPE
Ultraplan Eco is intended for internal works; for alignment of differences from 1 to 10 mm on the existing and new bases, before laying of any floor coverings where high resistance to loadings and the pedestrian movement is required. Ultraplan Eco is especially recommended for rooms where chairs on castors are used. Ultraplan Eco is intended for use only in rooms.
Some cases of application
- Alignment of concrete overlappings and cement it is heavy or couplers on the basis of such materials as Topcem, Mapecem or Topcem Pronto, Mapecem Pronto, the angidridny, magnesite bases, the warmed floors.
- Alignment of the existing floors from concrete, tiles of terazzo, ceramics and a natural stone.
DESCRIPTION OF MATERIAL
Ultraplan Eco - the gray powder consisting of special grades of the cements possessing a fast skhvatyvaniye and hydration, perfect sand, pitches and special additives is made according to the formula developed by research laboratories MAPEI. At a zatvoreniye Ultraplan Eco water forms the easy - flowing and light solution in application which is characterized by the fine self - leveled properties, high adhesion to the bases, superfast drying. Ultraplan Eco can give the concrete pump over 100 m of Ultraplan Eco are applied on distance up to 10 mm thick for a layer without shrinkage and cracking and becomes very strong on compression and a bend, very firm and resistant to chips and to attrition. Laying of coverings can be carried out approximately in 12 hours after alignment regardless of layer thickness. Before laying of wooden coverings it is recommended to wait 24 hours. Ultraplan Eco has very low emission of volatile organic compounds (EMICODE EC1) therefore it is absolutely harmless to health of stackers and users.
CONTRAINDICATIONS TO APPLICATION
- It is not necessary to add water to solution which already began to grab.
- Not to add cement, lime or plaster to mix.
- Not to use Ultraplan Eco for external works.
- Not to apply Ultraplan Eco on the bases subject to raising of capillary moisture.
- If there is a need to put one more layer of the given mix over the previous completely dried Ultraplan Eco layer, it is previously necessary to put a primer of Eco Prim T.
- Not to put at a temperature below + 5 °C.
- For the subsequent laying of wooden coverings not to put Ultraplan Eco less than 3 mm thick.
INSTRUCTION FOR APPLICATION
Preparation of the basis
The basis has to be completely dry, strong, cleared of dust and loose particles, paint, wax, oils, a rust and traces of plaster. If the cement bases insufficiently firm, them it is necessary to remove or if it is possible, to strengthen them by means of the strengthening structure of Ecoprim PU 1K, Prosfas or Primer MF. Cracks should be closed up by means of structure of Eporip. Dusty and very porous concrete surfaces should be processed a layer of a primer of Eco Prim T diluted with water 1: 1 or Primer G diluted with water 1: 3 (both primers have very low emission of volatile organic compounds - EMICODE EC1) to level the absorbing ability of the basis. For alignment of the angidritny bases at first it is necessary to put with the mix Ultraplan Eco surely a layer of a primer of Eco Prim T diluted with water 1: 1. At alignment of the bases from a ceramic tile and a natural stone at first they have to be cleared by the washing solutions and are mechanically processed (polishing), and then it is necessary to put a layer of an undiluted primer of Eco Prim T.
Preparation of working mix
Fill up Ultraplan Eco bag (23 kg) the vemkost containing about 5,8 pure l and mix the low - speed electric mixer before receiving uniform mix without lumps. Large numbers can be mixed in a concrete mixer. Leave weight to stand within 2 - 3 minutes and once again mix. Then solution is ready to application. At a thickness more than 10 mm (but no more than 20 mm) about 20 - 30% of sand fraction 0/4 or 0/8 of mm depending on the layer thickness (For obtaining more detailed information address to Department of technical support of MAPEI) are recommended to add. Mix should be produced within 20 - 30 min. (at a temperature of + 23 °C).
Putting mix
Apply Ultraplan Eco solution on the basis with a uniform layer from 1 to 10 mm thick by means of the wide metal pallet or a rakla, holding slightly under an inclination for creation of the required layer thickness. It is also possible to Ultraplan Eco to put by means of the concrete pump. Thanks to the high self - leveled ability of Ultraplan Eco instantly levels minor defects of a surface (traces of the pallet, etc. ) . If it is necessary, the second layer of Ultraplan Eco can be put when the first layer is ready to circulation (approximately in 3 hours at + 23 °C). The surface leveled by Ultraplan Eco is suitable for laying of elastic, textile and ceramic coverings in 12 hours at a temperature at + 23 °C (this time can vary depending on temperature and humidity indoors). Before laying of wooden coverings or a natural stone it is necessary to wait 24 hours. Humidity needs to be checked a kabidny or electronic hygrometer, considering at the same time that the last gives approximate values.
CLEANING
Fresh Ultraplan Eco can be removed from tools with water.
EXPENSE
1,6 kg/sq. m on each mm of thickness.
PACKAGING
Ultraplan Eco is delivered in bags on 23 kg.
STORAGE
At storage in the dry room of Ultraplan Eco completely keeps the characteristics within not less than 12 months. At excess of this term time of a skhvatyvaniye can increase, but final characteristics remain. It is made according to the Directive 2003/53/EC.
THE SAFETY RULE AT PREPARATION AND USE
This material contains cement which in contact with then and other corporal moisture leads to the irritating alkaline reaction and the allergic phenomena at the people predisposed to it. It is necessary to use protective gloves and points. More detailed data are given in the Material safety data sheet.
MATERIAL FOR PROFESSIONAL USE.
PREVENTION
The instructions which are contained in the present manual and recommendations reflect all depth of our experiment on work with this material, but at the same time they should be considered only as the general instructions which are subject to specification and practical experience. Therefore before widely applying material to an opredelennoytsela, it is necessary to check it for adequacy, to the provided type of the use, assuming all completeness of responsibility for the consequences connected with use of this material.