- Country of manufactureBelarus
It is intended for priming and strengthening loose, porous, fragile and grinding surfaces before applying water - dispersion paints and performance of the painting, wallpaper, plaster and flooring work on concrete, brick, plaster, putty and other porous surfaces. Due to the size of the ultrafine particle dispersion coating has a high penetrating ability into the upper layers of an inorganic base.
Primer can be used both for internal and for external works.
|«FRESKO Imprelid Ultra»|
|one||Appearance primer||Unclear - white liquid|
|2||Mass fraction of solids, %||15 ± 1|
|3||Hydrogen ion concentration, pH||6.0 - 8.0|
|4||Drying time to degree 3 at (20,0 ± 2) ° C, h, max||one|
Advantages: Primer practically odorless, reduces absorbency paintable base facilitates subsequent deposition of layers of paint provides uniform application of subsequent layers of paint, reducing paint consumption and ensures a strong bond with a base, economical and environmentally friendly.
The primer used for interior and exterior work.
Surface preparation: Before applying the primer with facades mechanically removed moss, tar spots. Surfaces having efflorescence necessary clean dry method (brushing). In operation the surfaces of this type can not ensure the durability of the coating, because of possible repeated appearance of salt deposits and, in consequence, the violation coating adhesion to the substrate.
The surface must be clean, dry, solid, exhibit good load bearing capacity and does not contain substances which reduce adhesion (release agents).
Fresh mineral surfaces (plaster, putty) before priming concrete should be conditioned for at least 28 days at a temperature not below 10 ° C, the allowable residual moisture bases - not more than 8% .
The old surface, previously painted with mineral paints, loosely hold the coating, peeling of the base, chalk or lime, chalk coating was removed completely washing apparatus under high pressure or by mechanical means. After wet cleaning is necessary to give the ground to dry well. Peeled surface and coating defects are aligned plaster solution or polymeric fillers, sanded and cleaned of abrasive residues. Glossy concrete surface is treated mechanically to give them a surface roughness (surface should be matte).
Panelists metal parts (valves, caps and nails etc. ) cleaned of rust and paint primer "Akvapraym" (TU BY 500021625.125) or primer "LidAkril" (TU BY 500021625.124), or primer enamel "Ekolyuks" (TU BY 500021625.145 ).
Coating: The primer is diluted with water and is stirred before use. Primer recommended dilution with water in a proportion of 1 to moderately absorbent surfaces: 1 for highly absorbent surfaces - 2: 1.
The primer is applied with brush, roller or brush in one - two layers (depending on the absorbency of the surface) at ambient temperature and the surface from plus 7 ° C to plus 35 ° C, under favorable weather conditions, i. e. in the absence of rain, strong wind or fog. After the rain hold staining should only after 2 - 3 days exposure surface at a temperature not lower than 15 ° C. Deviation from these recommendations may occur deterioration of performance and processability priming.
Drying Time coats at least 2 hours at ambient temperature (20 ± 2) ° C and a relative humidity of 65% .
When reducing the temperature or humidity change primer drying time is increased to 4 hours.
Primer «FRESKO Imprelid Ultra» when applied carefully rubbed into the surface. Properly primed surface should be matte, and in any case shall not shine.
Primer consumption of 100 - 125 g / m2, depending on the roughness, the porosity, absorbency of the substrate, the application method, etc. painter qualification factors. . More precisely flow is determined by applying a test coating.
Consumption primer priming with textured and highly absorbent surfaces can reach 200 g / m2.
Subsequent layers paint coating must be applied after 2 hours at a temperature of (20 ± 2) ° C and a relative humidity of 65% .
Not be mixed with other primer paints and solvents of any type. Diluted with water only.
Tool wash water container and not later than 10 - 15 minutes after application.
After using the primers as intended packaging with the product must be tightly closed residues closures and sent to the consumer landfill
Storage: The primer is kept in closed warehouses at ambient temperature from + 5 ° C to plus 35 ° C. Do not allow direct sunlight. In winter, the primer is transported in insulated truck.
Precautions: Priming fire and explosion. Persons related to the paint work must be provided with personal protective equipment (overalls, safety glasses, rubber gloves). In case of contact primer eyes, mucous membranes and skin and plenty of water.
The dried coating has no toxic effects on the human body.